Garage Door Cable Repair

    Got a problem with your garage door?

    Our team at A1 garage doors Is armed and ready.

    Phone ☎️ (647) 249-8443

    Or leave a message and we'll get right back to you.

    Send us some photos for an estimate.

    Garage Door Cable Repair

    Looking For a Garage Door Cable Repair Service?

    The cables on your garage door are another essential component that allows your door to function smoothly and facilitates your day-in and day-out.

    If your garage doors are not doing well, not only is our safety at stake, but our routine will be disrupted as well.

    What are you going to do if parts of your garage door stop working? We will give you tips on how you can fix cables on your own to power your garage door again.

    What’s Up With Your Garage Door Cables

    Garage door cables raise the garage door with power supplied from the spring system from the bottom fixture spool cables across the torsion drum and attach to raise the entrance to the bottom fixture. Garage door Cables will generally give a warning before complete disaster not the same for some springs that break down when the garage door is already closed.

    Replacement Reasons

    Old Fatigued Cables

    Roping Cable

    It indicates the first sign of garage door cable fatigue and is triggered by extending the cable with the torsion drums and pressure of your garage door.

    Looping Door Cable

    It is the second cable fatigue warning. This looping removes and raises the risk of fraying from the individual cable fibres and induced because of unnecessary roping. Loose loops open on the cables.

    Fraying Garage Door Cable

    Roping leads to Looping and Fraying, and this is the third indication that you need to remove your cable. Visible breaks in the cable for the individual fibres which make up a garage door.

    Garage Door Cable Replacement is strongly advised from here, as this is the only issue you will encounter. It could lead to a massive problem with the garage door if you let that one slide.

    Damage Caused Outside Of Regular Use

    If cables are kinked, then we suggest removing the garage door cable to avoid fraying or possible spooling issues in the future.

    • Even drums will start losing their cable pulling grooves. Whenever these Flatten Out, it Will Roll The Cable on its own and Break The Fibers. Drums may create burrs that break cords, and can be beaten down by the sharp edges of cable formation which can split wire fibres.
    • Don’t cut torsion cables if you don’t want to have more problems with your garage door.

    When to know if your garage door cable is not working?

    You may usually see a cable or wire hanging near your garage door, or you will also find that perhaps the springs look fine and are not damaged, but the door is not working. It just means something is wrong, and your garage door needs improvement.

    #1. Lock the Door Down

    Buckle a C-clamp or locking pliers to the line right above one of the rollers. And, before you launch any spring and cable repair, pull the cable and unplug the garage door opener.

    #2. Loosen Working Springs

    Cram a revolving bar into a bottom hole of the strong spring’s winding rod. Keep bars in position as the two set screws loosen. Saddle up; when the bolts loosen, the spring will move with strong torque. Unwind the loose springs after then remove them from the centre bracket.

    #3. Securing the Torsion Tube

    To keep the torsion tube in the bracket, clamp a tightening pin or a C-clamp onto the middle bracket and release the set screws on both sides of the lift cable drum and remove the lift cables.

    Slip right the torque tube to the right from the left side of the frame, so that you can detach the cable drum. Then slide out the tube from the original spring.

    #4. Rollers, Lift Cables and Brackets Replacement

    After the left spring and centre bearings are attached, clip the lift cable loop onto the new bottom bracket over the bolt. Place the new roller in and add in new cables and brackets at the bottom.

    #5. Anchor the Cables

    Push the wire or lift cables directly up between both the rollers and the door jamb. Then, drag the cable lift stop over the drum slot. Strengthen the drums by equalizing the tension after.

    #6. Winding and Stretching Springs

    Drag into a cone a revolving rope, and wind towards the roof. Switch the spring one-quarter switch at a time, outrunning bars as you go. Push the revolving bar to extend the spring about 1/4 inches from the middle before set screws tightened.

    #7. Lubrication

    Clog up the spring with lube spray on the garage door. Then clean up the waste.

    If you happen to be living near such places as Mississauga, Richmond Hill, Vaughan, Woodbridge and need a qualified garage repair assistant but too busy to follow the following guide that we are about to show you, please do not hesitate to contact us via our website or call us.

    5/5 - (1 vote)

    Hope you enjoyed our article titled Garage Door Cable Repair. Besides "Garage Door Cable Repair", feel free to browse our blog for more great content. A1 Garage Doors.

    Garage Door Cable Repair
    Contact Us
    Contact Us!

    Garage door repair A1

    Looking for a quick garage door repair?
    Need a routine tune-up or maintenance?

    CALL NOW: ☎️ (613) 704-7698



    We service Ajax, North York, Oakville, Richmond Hill, Pickering, Etobicoke and the wider Mississauga area.

    Our technicians are equipped with masks and gloves complying with health and safety regulations.
    This is default text for notification bar